Addressable wireless fire alarm – Series 200A
DAS-FACP-200AAddressable wireless fire alarm control panel
Control panel of the Tan Vien Series 200A addressable wireless fire alarm system.
- Manages up to 550 wireless devices (50 + 10 repeaters × 50)
- 4.3″ color LCD showing the address and signal strength of each device
- 1 fire relay + 1 fault relay (dry contacts)
- AC 110/220 V or DC 24 V supply, 7.2 V / 4000 mAh backup battery
Price on request
The brain of the entire system: embedded microprocessor, 4.3″ color LCD, a built-in internal repeater (repeater No. 0) and management of up to 10 external repeaters — 550 wireless devices in total, displaying in real time each device's address, signal strength and connection status.
550wireless devices per panel
10external repeaters (10 levels)
4.3″color LCD
Key features
- Intuitive interface. Embedded microprocessor, 4.3″ color LCD, key-operated menu.
- Built-in LoRa. Repeater No. 0 sits inside the panel and directly manages 50 devices + 10 external repeaters.
- Real-time signal monitoring. Check the RSSI/SNR of each repeater and device directly on the panel.
- 2 dry-contact relay outputs. 1 fire relay + 1 fault relay — for connecting alarm transmission devices to report incidents.
- Interlock programming & isolation. Address-based interlocking; isolate (disable) individual devices during maintenance.
- Commissioning and acceptance support. Manually switch each I/O module or sounder beacon on/off for point-by-point testing.
- On-site software upgrade. Update the firmware directly; no need to take the panel back to the workshop.
- Ready for expansion. Reserved hardware for CAN bus panel networking, WiFi / Bluetooth / 4G (next development phase).
Installation notes
- Install where staff are on duty 24/7; controls at 0.8 – 1.8 m above the floor.
- Preferably powered from the fire protection supply; if mains power is used, make sure it cannot be cut off.
- Each panel in the same project must have its own Network ID.
For detailed network registration, installation and commissioning procedures, see Series 200A Design, Installation and Operation Manual (PDF).
Suitable installation locations
DAS-FACP-200A technical specifications
| Model | DAS-FACP-200A |
|---|---|
| Main power | AC 110 V / 220 V – 50 Hz or DC 24 V |
| Backup power | Lithium battery DC 7.2 V / 4000 mAh |
| Transmission technology | LoRa 312 – 316 MHz, transmit power ≤ 20 dBm |
| Transmission range | 1000 m (unobstructed – manufacturer's figure) |
| Capacity | 50 direct + 10 repeaters × 50 = 550 devices; cascade ≤ 10 levels |
| Communication fault level | Level I ≤ 300 s · Level II ≤ 2 h |
| Network ID | 1 – 254 (each panel in a project has its own ID) |
| Output | 1 fire relay + 1 fault relay (dry contacts) |
| Networking / IoT | CAN bus; WiFi, Bluetooth, 4G reserved (phase 2) |
| Environment | −10 °C to +55 °C; RH ≤ 95 % (40 ± 2 °C) |
| Reference standards | TCVN 7568-2 · TCVN 7568-4 · TCVN 7568-25:2023 (ISO 7240-25) |
Related products
DAS
DAS-WSD-200A
Addressable wireless photoelectric smoke detector
Price on request
DAS
DAS-WHD-200A
Addressable wireless fixed-temperature heat detector
Price on request
DAS
DAS-WCP-200A
Addressable wireless emergency manual call point
Price on request
DAS
DAS-WSB-200A
Wireless combined fire alarm sounder beacon
Price on request
DAS
DAS-WIO-200A
Wireless I/O control module
Price on request